How to Replace the Replacement Key Battery For the Saab 9-3
Saab owners have a distinct procedure to add an additional key. It requires dealer service with a handheld computer dubbed Tech-2. A new key and transponder are required to be purchased and programmed to the car.
It is a good idea to rotate your keys so that one does not wear out more quickly than the other. This will also ensure that your keys remain in good condition.
Replacement Case
The new key fobs for keys are not like the old Saab keys. They feature electronic components which make it hard to copy. That has made car theft significantly more complicated than it was 20 years ago. It also makes it more costly to replace keys that were lost.
Saab 9-3 owners must have two working keys. It is expensive to replace a lost key as it requires replacing the CIM module, as well as reprogramming the locking cylinders. Dealers charge between $100 and $200 to do this.
There are several ways to get around these expensive. Some parts retailers will find the code from a spare key (usually the same one that opens the doors and turns off the ignition) and cut a new key blade from metal for a fraction of the dealer’s cost. The key must be exactly the same as the original in order for it to work in your vehicle.
You can also replace the case yourself by following these steps. You’ll require a flathead and patience. Utilizing the screwdriver, slowly tear the plastic away and remove the emergency key from the case. Once the case is open, remove the electronics and place them into the new case. Put the correct key and badge into the case.
Replacement Battery
The Saab 9-3 replacement battery is a cheap component that can be easily and quickly replaced. This YouTube tutorial for DIY Cyclone Cyd shows how to replace the battery for the remote key fob in just four steps. This tutorial is compatible with any modern Saab spare key key fob. However, the procedure could differ slightly.
The button is normally located near the saab key battery replacement logo on the back of the fob. It’s usually near the Saab logo on the back of the fob. Use a flathead screwdriver to insert the screwdriver into the small hole on this button. This should be enough to unlock the case of the fob so that you can replace the battery.
Once the new CR1632 battery is in place You can then reassemble the remote key fob. You can then program it to your car. The entire process should take no more than an hour at most. This is a very easy procedure that doesn’t require special tools.
The process is a bit more complicated in the event that you lose your key, but it is possible. The dealer must first read the VIN of the vehicle and then order an additional TWICE module and key blade that has the correct unique code. The dealer will then have to program the key using MDI which is a new software tool.
Key Replacement Fob
The key fob is a device that locks and unlocks your car. It is equipped with an internal battery. Batteries have a limited lifespan and eventually will die. It’s a common issue with all cars. The good news is that you can replace the battery in all key fobs without having to replace the entire case. You can buy replacement fobs on Amazon that come with all the electronic components already installed, which means you can simply open the case and replace those batteries that are old. It’s important to note that you will need to take out the emergency key first, and you can accomplish this by inserting the small screwdriver flathead into the slot found in the middle of the case. The case will split when you rotate the screwdriver around it.
If you’re ready to change your keys, have an extra set on hand. This will save you a lot of money. If you have a spare you can ask the dealer cut the new key and program it to your car, which is cheaper than replacing the entire key fob.
It is possible to add a second key to your vehicle in the event that you don’t have one, but it requires lots of research and effort. It will cost you a few hundred dollars to get an additional car key. The computer in the vehicle must also be programmed. Professionals can do this but it’s not a cheap option.
Replacement Ignition
The new SAAB 9-3 uses an advanced alarm system built around a key code. This means that if you lose your only functioning key, getting an additional one could be extremely expensive since the car has to have a special computer module installed, and it must also be specifically programmed to accept a new key. Most locksmiths can’t do this or even dealers can charge several hundreds of dollars just to program the new key!
Dealers will charge you the highest price to replace your car’s computer (also known as the CIM or SAAB twice) in the event that you lose the only working key. Instead we can reprogram the EEPROM on your existing car computer, preparing it for a new key, which will save you more than 50% of what you’d pay at a dealership.
If you’ve owned a 9-3 from SAAB for a long time and you’re aware of the ignition keys aren’t very durable. They can become extremely sticky and the buttons are known to fall off at times It is recommended that you consider getting a replacement if yours isn’t performing as it should. It’s good to know that replacing the ignition key isn’t as difficult as it sounds, and it is fairly easy to do using the right tools.